WHY LEARNING PLUMBING BASICS IS CRUCIAL FOR INSTALLING A BATHTUB

Why Learning Plumbing Basics is Crucial for Installing a Bathtub

Why Learning Plumbing Basics is Crucial for Installing a Bathtub

Blog Article

Visit Link

Every person has their private conception about Tools You Need to Install a New Bathtub .


Tools You Need to Install a New Bathtub
Mounting a bathtub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old tub with a new one is also a reasonably difficult project. If the old bathtub is easily available, the task can move easily; if you have to open up a wall surface to remove the old tub as well as place the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed task, it is far better to think about employing one before you start. Opportunities are you might need a specialist plumber to make tube links.
This article will assist you set up a new bathtub in your shower room if you have already bought a brand-new bathtub as well as don't require to alter the plan of your previous water system pipes.
Your devices as well as material list should consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Setup


    First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
    Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final setting.

    Removing Old Touches


    If you require to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the restricted gain access to that is typically the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
    Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Setting up the Tub


    Utilizing the two wood boards under its feet, put the tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
    The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bathtub until the spirit level reviews level.
    To set up faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
    Switch on the water system as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill up the tub as well as likewise examine the overflow electrical outlet as well as the regular outlet for leaks.
    Finally, take care of the bath paneling as explained in the producer's user's manual. Tiling and sealing around the tub must wait until the bathtub has actually been made use of a minimum of when as this will certainly settle it into its final setting.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end gives a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The former kind should be linked to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing complications with moisture and feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bathtub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not consider this movement before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you enjoy reading about How to Install a Bathtub Yourself? Try leaving a remark further down. We would be glad to know your reactions about this content. In hopes that you come back again soon. Do you know another person who is interested by the topic? Feel free to promote it. We recognize the value of reading our article about How to Install a Bathtub Yourself.


    Ensure leak-free homes.

    Report this page